holybroHolybro· Cartes & informatique embarquée
Pixhawk Jetson Baseboard Bundle
Réf. fabricant 20338
2480.00 $≈ 2149.23 €
Le prix en résumé
Vendu par holybro à 2149.23 €. Livré en France, port, TVA et droits de douane éventuels compris, il revient à environ 2597.08 €. Prix relevés le 2026-09-16.
Le coût livré est une estimation pour un article seul expédié en France métropolitaine ; seul le panier du vendeur fait foi.
Disponibilité inconnue
Coût total livré estimé
| Article | 2149.23 € |
|---|---|
| Frais de port | 15.00 € |
| TVA (20 %) | 432.85 € |
| Total livré | 2597.08 € |
Estimation pour un article seul livré en France métropolitaine, expédié hors UE : des droits de douane et frais de dédouanement peuvent s'ajouter, facturés par le transporteur.
Caractéristiques (extraites automatiquement)
Mécanique
| Poids | 820 g |
Description
Description The Holybro Pixhawk Jetson Baseboard is based on the Pixhawk Bus open source specification and the NVIDIA Jetson Orin NX/Nano Carrier Board. The Pixhawk Bus (PAB) Form Factor enables this to be used with any PAB flight controller, such as the Pixhawk 6X Feature Combines the power of Pixhawk & Nvidia Jetson in a single board Nvidia Jetson & Pixhawk connected via UART, CAN, and ethernet switch Pixhawk Bus (PAB) Form Factor Compatible with Jetson Orin NX & Orin Nano 2x M.2 key for WiFI/Bluetooth & NVMe SSD Pixhawk 6X (ICM-45686) Processors & Sensors FMU Processor: STM32H753 32-bit Arm® Cortex®-M7, 480MHz, 2MB flash memory, 1MB RAM IO Processor: STM32F103 32 Bit Arm® Cortex®-M3, 72MHz, 64KB SRAM On-board sensors (Shipping Currently, Rev8) Accel/Gyro: 3x ICM-45686 (with BalancedGyro™ Technology) Barometer: ICP20100 & BMP388 Mag: BMM150 Baseboard Port & Connection Jetson Connectors 2x Gigabit Ethernet port Connected to both Jetson & Pixhawk via Ethernet switch (RTL8367S) Ethernet Switch powered by circuit as the Pixhawk 8-pin JST-GH RJ45 2x MIPI CSI Camera Inputs 4 Lanes each 22-Pin Raspberry Pi Cam FFC 2x USB 3.0 Host Port USB A 1.5A Current Limit 2x USB 2.0 Host Port 5-Pin JST-GH 1.0A Current Limit USB 2.0 for Programming/debugging USB-C Key M 2242/2280 for NVMe SSD PCIEx4 Key E 2230 for WiFi/BT PCIEx2 USB UART I2S Mini HDMI Out 4x GPIO 6-pin JST-GH CAN Port Connected to Pixhawk's CAN2 (4 Pin JST-GH) SPI Port 7-Pin JST-GH I2C Port 4-Pin JST-GH I2S Port 7-Pin JST-GH 2x UART Port 1 for debug 1 connected to Pixhawk's telem2 Fan Power Port IIM42652 IMU Input Power XT30 Connector Voltage Rating: 7-21V (3S-4S) Separate input power circuits from the Pixhawk to ensure flight safety Holybro UBEC 12A (3-14S) can be used for applications above 4S Note: The Pixhawk Jetson Baseboard onboard BEC is only rated for 7- 21V (3S- 4S). Using the external "UBEC 12A (3-14S)" can provide redundancy and easier replacement in case of BEC failure. Power Requirements 8V/3A Minimum Dep
