racedayquadsRUNCAM· Commande de moteurs
SpeedyBee F405 V5 Stack - F405 FC + 55A 3-6S OX32 ESC - 30x30 - Standard
Réf. fabricant G24775CN1Z
142.79 $≈ 123.75 €
Réf. fabricant G24775CN1Z
Vendu par racedayquads à 123.75 €. Livré en France, port, TVA et droits de douane éventuels compris, il revient à environ 166.50 €. Prix relevés le 2026-09-16.
Le coût livré est une estimation pour un article seul expédié en France métropolitaine ; seul le panier du vendeur fait foi.
| Article | 123.75 € |
|---|---|
| Frais de port | 15.00 € |
| TVA (20 %) | 27.75 € |
| Total livré | 166.50 € |
Estimation pour un article seul livré en France métropolitaine, expédié hors UE : des droits de douane et frais de dédouanement peuvent s'ajouter, facturés par le transporteur.
| Courant | 55 A |
| Poids | 127 g |
The SpeedyBee F405 V5 Stack - F405 FC + 55A 3-6S OX32 ESC - 30x30 - Standard features an upgraded F405 flight controller and OX32 ESC. With the built-in Bluetooth chip, use Betaflight to tune in the field. With a built-in barometer and connectivity to all DJI Air Units, along with UART ports for maximum customizability, this stack was crafted with precision - your all-in-one choice for top performance. Check out all our 30x30 stacks & combos, and all our Speedy Bee products! Features New clock sync function improves detection accuracy Easier soldering with added direct sockets for GPS and receiver Nickel-plated bus bars Double-sided heat-spreading Wireless tuning and upgrading Specifications F405 FC MCU: STM32F405 IMU (Gyro): ICM42688P USB Port Type: Type-C Barometer: SPA06-003 OSD Chip: AT7456E Bluetooth Tuning: Supported. Connect via SpeedyBee App for FC firmware flashing and parameter tuning Wireless FC Firmware Upgrade: Supported DJI Air Unit Connection: Supports 6-pin direct plug-in or solder connection Blackbox: Supported, built-in 16MB storage chip Input Voltage: 3-6S LiPo Battery 5V BEC Output: 9 groups (4x +5V pads, 1x BZ+ buzzer pad, and 4x 5V pads at corners for LEDs 9V BEC Output: 2 groups (1x 9V pad on front, 1x 9V pad on back). Supports PINIO remote on/off control MCU & Gyro Power: Independent LDO 3.3V Output: 1 group (1x 3.3V pad on front) 4.5V Output: 3 groups (3x 4.5V pads on front) Can power receiver & GPS when FC is powered via USB. Max current 1A. ESC Signal: M1-M4 pads and 10-pin connector on back Servo Signal: S5-S6 pads on the front ESC Telemetry Input: Supported (UART 5) Betaflight Camera Tuning Pad: Supported (CC pad on front) I2C: Supported (GPS connector + pads) UART UART1: Bluetooth UART2: front pads for receiver UART3: DJI VTX pads + 6-pin SH1.0 UART4: GPS pads + front 6-pin SH1.0 UART5: TLM UART6: receiver pads + rear 4-pin SH1.0 ST LED Pads: Supported, on front G/5V/LED Meteor LED Strip Pads: Supported Buzzer Pads: Supported BOOT Butto
