racedayquadsMATEK· Capteurs
Matek AP_Periph Drone CAN GNSS - M10-L4-3100 - GPS
Réf. fabricant 19251
107.09 $≈ 92.81 €
Le prix en résumé
Vendu par racedayquads à 92.81 €. Livré en France, port, TVA et droits de douane éventuels compris, il revient à environ 129.37 €. Prix relevés le 2026-09-16.
Le coût livré est une estimation pour un article seul expédié en France métropolitaine ; seul le panier du vendeur fait foi.
Disponibilité inconnue
Coût total livré estimé
| Article | 92.81 € |
|---|---|
| Frais de port | 15.00 € |
| TVA (20 %) | 21.56 € |
| Total livré | 129.37 € |
Estimation pour un article seul livré en France métropolitaine, expédié hors UE : des droits de douane et frais de dédouanement peuvent s'ajouter, facturés par le transporteur.
Caractéristiques (extraites automatiquement)
Mécanique
| Poids | 32 g |
Description
The Matek AP_Periph Drone CAN GNSS - M10-L4-3100 has a GPS, Compass, and Barometer! Ready for whatever your aircraft can throw at it! Check out our GPSs, BECs, PDBs, Sensors and all of our Matek Products! Features M10-L4-3100 is based on ArudPilots’ AP_Periph firmware, It is a GNSS+COMPASS+BAROMETER peripheral with CAN/DroneCAN and UART/MSP interfaces. M10-L4-3100 uses multi-constellation GNSS powered by u-blox M10 series , It is a concurrent GNSS receiver which can receive and track multiple GNSS systems. Owing to the multi-band RF front-end architecture all four major GNSS constellations, GPS,Galileo, GLONASS and BeiDou can be received concurrently. M10-L4-3100 integrates an industrial-grade compass PNI RM3100 which provides high resolution, low power consumption, no hysteresis, large dynamic range, and high sampling rates. Specifications ublox GNSS M10 series (GPS, GLONASS, Galileo and BeiDou) Magnetic Compass: RM3100 Barometer: SPL06-001 Patch GNSS Antenna: 25x25x4mm MCU STM32L431RCT6 UART3, onboard M10 GNSS module UART2(TX2 RX2), MSP Protocol CAN, DroneCAN Protocol I2C JST-GH connector for external AirSpeed sensor CAN bootloader LED, Blue Fast blinking, Booting Slow blinking, working GNSS PPS LED, Green solid on after powering on blinking(1Hz) when GNSS has 3D fixed 3.3V LED, Red Input voltage range: 4.5~5.3V (5V pad/pin) Power consumption: 60mA Operating Temperatures: -20~80 °C Dimensions: 36mm*36mm*12mm Weight:16g Firmware ArduPilot AP_Periph: MatekL431-GPS or MatekL431-Periph Tips & Notes on M10-F4-3100, The 3 magnetic coils have little solder paste to avoid the excess to “tilt” them, resulting in some reading inaccuracies of the compass. Any strong impacts will definitely separate them, especially the “tall coil” Sen-Z-f. Please use this precision module with care. The default configuration on MAX-M10S with ublox FW5.1 is concurrent reception of GPS, Galileo, and BeiDou B1I with QZSS and SBAS enabled. GLONASS is disabled by default. Beidou B1I (1561.098 MHz
