MÄDLERMÄDLER
Cardan joint KE outer diameter 20mm no bore material steel total length 62mm
Réf. fabricant 63002000
51.37 $≈ 44.51 €
Le prix en résumé
Vendu par MÄDLER à 44.51 €. Livré en France, port, TVA et droits de douane éventuels compris, il revient à environ 71.41 €. Prix relevés le 2026-08-05.
Le coût livré est une estimation pour un article seul expédié en France métropolitaine ; seul le panier du vendeur fait foi.
En stock — 2 unitésdélai 14 j
Coût total livré estimé
| Article | 44.51 € |
|---|---|
| Frais de port | 15.00 € |
| TVA (20 %) | 11.90 € |
| Total livré | 71.41 € |
Estimation pour un article seul livré en France métropolitaine, expédié hors UE : des droits de douane et frais de dédouanement peuvent s'ajouter, facturés par le transporteur.
Documentation technique
Caractéristiques (extraites automatiquement)
Mécanique
| Poids | 138 g |
Autres caractéristiques
| Length of bolt | 21.5 mm |
| Length of bore | 18 mm |
| Max torque | 20 Nm |
| Outer diameter | 20 mm |
| Total length | 62 mm |
| Bore diameter | Without bore mm |
| Material | Steel (12L13) |
| Surface | Blank |
| Version | A |
Description
Material: Steel 11SMn30 (1.0715). Max. Operating Angle 45°. The cardan joints KE are, other than the cardan joints with needle-roller bearing, only sliding-contact bearings. Their scope of application is therefore limited to slow running drives. The respective maximum speeds depend on operating angle and load, but must never exceed 1000 rpm. The maximum torque values listed in the table are limits, which must neither be exceeded. They may only be used to their full extend with intermittent operation or at low speed. The following limit applies: The product of speed (rpm) x working angle (degrees) may not exceed the reference number 500. This means, e.g., for a working angle of 10 degrees a max. speed of 50 rpm. If, however, the maximum torque is not taken to the limit, speed and working angle can be larger. At 0.5 x max. torque applies: speed x working angle, smaller or equal 4.000. In case of doubt choose larger joint. At continuous operation the cardan joints need to be sufficiently lubricated. If no drip-feed lubrication is possible, lubricate the joints at least once a day. Another possibility is to cover the joints with a bellow, filled with a suitable lubricant. Typ A: without bores. Type B: with bores. Type N: with bores and keyways DIN 6885-1 on both sides.
Alternatives moins chères
Produits sémantiquement proches et moins chers — vérifiez que les caractéristiques correspondent à votre besoin.
MÄDLEREn stock
Cardan joint KE outer diameter 13mm no bore material steel total length 42mm
34.78 €40.14 $
Voir chez le vendeur ↗MÄDLEREn stock
Cardan joint KE outer diameter 13mm both sides bore 8H7 material steel total length 42mm
35.68 €41.18 $
Voir chez le vendeur ↗Produits similaires
MÄDLERSur commande
Cardan joint KE outer diameter 20mm both sides bore 12H7 material steel total length 62mm
39.40 €45.48 $
Voir chez le vendeur ↗MÄDLERSur commande
Cardan joint KE outer diameter 63mm no bore material steel total length 166mm
200.49 €231.41 $
Voir chez le vendeur ↗MÄDLEREn stock
Cardan joint KE outer diameter 32mm no bore material steel total length 86mm
63.20 €72.95 $
Voir chez le vendeur ↗MÄDLERSur commande
Cardan joint KE outer diameter 50mm no bore material steel total length 132mm
119.31 €137.71 $
Voir chez le vendeur ↗