MÄDLERMÄDLER
Cardan joint KE outer diameter 25mm both sides bore 16H7 material steel total length 74mm
Manufacturer part no. 63012500
$55.99≈ 48.46 €
Price summary
Listed by MÄDLER at €48.46. Delivered to France, including shipping, VAT and any customs duty, it comes to about €76.15. Prices last checked on 2026-08-05.
Delivered cost is an estimate for a single item shipped to mainland France; the seller's checkout is authoritative.
In stock — 6 unitslead time 14 d
Estimated landed cost
| Item | €48.46 |
|---|---|
| Shipping | €15.00 |
| VAT (20%) | €12.69 |
| Total delivered | €76.15 |
Estimate for a single item delivered to mainland France, shipped from outside the EU: customs duty and clearance fees may apply and are charged by the carrier.
Datasheets & documents
Specifications (automatically extracted)
Mechanical
| Weight | 160 g |
Other characteristics
| Bore diameter | 16 mm |
| Length of bolt | 26.5 mm |
| Length of bore | 22 mm |
| Max torque | 30 Nm |
| Outer diameter | 25 mm |
| Total length | 74 mm |
| Material | Steel (12L13) |
| Surface | Blank |
| Version | B |
Description
Material: Steel 11SMn30 (1.0715). Max. Operating Angle 45°. The cardan joints KE are, other than the cardan joints with needle-roller bearing, only sliding-contact bearings. Their scope of application is therefore limited to slow running drives. The respective maximum speeds depend on operating angle and load, but must never exceed 1000 rpm. The maximum torque values listed in the table are limits, which must neither be exceeded. They may only be used to their full extend with intermittent operation or at low speed. The following limit applies: The product of speed (rpm) x working angle (degrees) may not exceed the reference number 500. This means, e.g., for a working angle of 10 degrees a max. speed of 50 rpm. If, however, the maximum torque is not taken to the limit, speed and working angle can be larger. At 0.5 x max. torque applies: speed x working angle, smaller or equal 4.000. In case of doubt choose larger joint. At continuous operation the cardan joints need to be sufficiently lubricated. If no drip-feed lubrication is possible, lubricate the joints at least once a day. Another possibility is to cover the joints with a bellow, filled with a suitable lubricant. Typ A: without bores. Type B: with bores. Type N: with bores and keyways DIN 6885-1 on both sides.
Cheaper alternatives
Semantically close products available for less — check the specs match your need.
MÄDLERIn stock
Cardan joint KE outer diameter 13mm no bore material steel total length 42mm
€34.74$40.14
View at seller ↗MÄDLERIn stock
Cardan joint KE outer diameter 13mm both sides bore 8H7 material steel total length 42mm
€35.64$41.18
View at seller ↗Similar products
MÄDLERIn stock
Cardan joint KE outer diameter 25mm no bore material steel total length 74mm
€47.44$54.81
View at seller ↗MÄDLERBackorder
Cardan joint KE outer diameter 16mm both sides bore 10H7 material steel total length 52mm
€35.08$40.53
View at seller ↗MÄDLERBackorder
Cardan joint KE outer diameter 20mm both sides bore 12H7 material steel total length 62mm
€39.36$45.48
View at seller ↗MÄDLERIn stock
Cardan joint KE outer diameter 63mm both sides bore 40H7 material steel total length 166mm
€210.97$243.75
View at seller ↗