racedayquadsDarwinFPV
DarwinFPV HULK F411/45A 3-6S AIO Flight Controller w/ SPI ELRS 2.4GHz
Manufacturer part no. 21285
$185.63≈ 160.87 €
Price summary
Listed by racedayquads at €160.87. Delivered to France, including shipping, VAT and any customs duty, it comes to about €211.04. Prices last checked on 2026-09-16.
Delivered cost is an estimate for a single item shipped to mainland France; the seller's checkout is authoritative.
Availability unknown
Estimated landed cost
| Item | €160.87 |
|---|---|
| Shipping | €15.00 |
| VAT (20%) | €35.17 |
| Total delivered | €211.04 |
Estimate for a single item delivered to mainland France, shipped from outside the EU: customs duty and clearance fees may apply and are charged by the carrier.
Specifications (automatically extracted)
Electrical
| Current | 45 A |
Mechanical
| Weight | 73 g |
Description
This AIO has a rating of IP67, In ideal conditions submersion of 1 meter for 30 minutes can be achieved. Introducing the all-new DarwinFPV Hulk AIO! Having IP67 water-resistant grading, 45A BLS ESC, and Onboard ELRS SPI receiver. This AIO is ready for any adventure that you can and couldn't take your drone!!! Check out our other AIO Flight Controllers and our Darwin FPV products! Specifications AIO F411 MCU: STM32F411CEU6 Gyro: MPU6500 OSD Chip: Betaflight OSD AT7456E Blackbox: 16MB UARTS: 5 I2C: SDA / SLA pads LED: Yes Beeper: Yes Firmware Target: MATEKF405 FC Mounting Pattern: 30x30mm Dimensions: 37x36x10.8mm AIO ESC Input Voltage: 2-6S Max. Continuous Current: 45A Max. Burst Current: 55A MCU: EFM8BB21F16G Current Sensor: Yes Mounting Dimensions: 25 x 25 M2 Dimensions 46.2mm x 39.5mm x 10mm Includes 1x Darwin FPV HULK F411/45A 3-6S AIO w/ ELRS 2.4GHz Please attention: Seawater is highly corrosive, it is not recommended for use in seawater. Please wash it with fresh water immediately and then dry it. Supports a 3-6S battery, remember not to plug the battery's positive and negative interface in reverse, otherwise, it will burn out. After receiving the AIO, first connect to a computer on Betaflight software to check whether the gyroscope and accelerometer are detected and whether the gyroscope attitude is normal. Increase the throttle in Betaflight software to ensure the normal rotation and correct rotation direction of the 4 motors, and then install the propellers for a test flight; be sure to remove the propellers when pulling the throttle in Betaflight software to avoid accidents. After confirming the above precautions without any problems, you can install the propellers and start flying! Wiring Diagram
Similar products
racedayquadsIn stock
HappyModel Crazybee F4 Lite 1S Whoop Flight Controller for Mobula6 - Choose Your RX
€80.43$92.81
View at seller ↗
racedayquadsIn stock
HappyModel 1S F4 AIO Toothpick/Whoop Flight Controller w/ 5A 8bit 4in1 ESC & 200mW VTX - ELRS 2.4GHz SPI
€86.62$99.95
View at seller ↗
racedayquadsIn stock
EMAX Tinyhawk 3 1-2S F4 AIO Flight Controller 5A ESC 25/100/200mW VTX
€111.37$128.51
View at seller ↗
racedayquadsIn stock
iFlight Blitz F411 1S 5A Toothpick/Whoop Flight Controller w/ 25-50mW VTX & ELRS RX
€86.62$99.95
View at seller ↗
