holybroHolybro
PM07 Power Module (14S)
Manufacturer part no. 15008
$43.99≈ 38.12 €
Price summary
Listed by holybro at €38.12. Delivered to France, including shipping, VAT and any customs duty, it comes to about €63.74. Prices last checked on 2026-09-16.
Delivered cost is an estimate for a single item shipped to mainland France; the seller's checkout is authoritative.
In stock
Estimated landed cost
| Item | €38.12 |
|---|---|
| Shipping | €15.00 |
| VAT (20%) | €10.62 |
| Total delivered | €63.74 |
Estimate for a single item delivered to mainland France, shipped from outside the EU: customs duty and clearance fees may apply and are charged by the carrier.
Also available second-hand on eBay
up to 39% off new
Holybro Power Distribution Board PDB for PM02 PM02D PM03 PM06 PM07 Power Module
New · sold by xghobby-us9 · ships from CN
Imported from outside the EU — duties and VAT included in the delivered cost; customs formalities and delays are not
Visit ↗€14.65
billed $16.91
€23.10 delivered
HolyBro PM07 Power Management PM Module for Pixhawk 4 PX4 FC RC FPV Racing Drone
New · sold by lhii5422 · ships from CN
Imported from outside the EU — duties and VAT included in the delivered cost; customs formalities and delays are not
Visit ↗€48.87
billed $56.39
€51.86 delivered
High Efficiency PM07 Power Management Module Pixhawk 4 PX4 Drone Power Supply
New · sold by xghobby-us_5 · ships from CN
Imported from outside the EU — duties and VAT included in the delivered cost; customs formalities and delays are not
Visit ↗€60.34
billed $69.63
€64.94 delivered
Third-party listings on eBay, matched to this product by its part number or title. Robotitem neither sells nor warrants these items: condition, stock and lead times are the seller's, and a listing disappears once sold. Delivered cost includes the seller's actual shipping.
Specifications (automatically extracted)
Mechanical
| Weight | 90 g |
Description
Description: This PM07 Power Module supplies clean 5.2V to flight controller from the battery and provides current consumption and battery voltage measurements via analog signal through a 6 Pin JST-GH cable, along with integrated esc power & signal distribution for up to 8 ESCs. PM07 has two 5.2V power output port that can provide redundant power to the flight controller, with independent circuits, BEC IC and circuitry. It is also great for flight controller that do not have built-in servo header pins like the Pixhawk 6C & Pixhawk 4. It comes with pre-soldered wires, capacitor, and XT60 connector. Specifications： Input voltage: 2S-14S PCB Cont. Current Rating: 90A PCB Burst Current Rating: 140A (<60 Sec) Output: DC 5.2V & 3A Max Voltage Divider: 18.182 Amperes per Volt: 36.364 Please Note: The PM07 12S version has been discontinued and replaced by the 14S version. The XT60 Plug and 12AWG wire that are pre-soldered on the board is rating for 30A continuous current and 60A burst current (< 60 Seconds). If a higher current is being used, the plug type and wire size should be changed accordingly. You can refer to this chart for reference. This PM07 Power Module uses analog data output and is not compatible to the Pixhawk 5X & 6X (Requires a digital PM like PM02D). Mechanical Specification: Dimensions:68*50*10 mm Mounting Holes:45*45mm Weight: 43.8g Setup guide for PX4 & Ardupilot can be found in the Holybro Doc here. PM07 User guide can be found here Package Include: 1x PM07 board 1x 80mm XT60 connector wire (installed) 1x Electrolytic capacito: 220uF 63V (installed) 2x JST GH 10P Cable 1x JST GH 8P Cable 2x JST GH 6P Cable
